QuinTech Brennstoffzellen Technologie
Research & Development
Test Equipment
Fuel Cells & Cells
Reformer
Components
Accessories
• Fuel Cell Repair Kit
• Heaters
• Gas Flow Back Pressure Regulator
• Swagelok Fittings
• Nylon & Teflon Shoulder Washers
• End Plates
• Die-Cuts
Cutting Dies & Presses
Education & Demonstration
Application
Special Offer
Technical Information
 
 
Accessories
Fuel Cell Repair Kit

Specification and Price:

Item
Description
Price €

EC-RPR-01*
EC-RPR-05*
EC-RPR-25*

includes: 8 bolts, 8 nuts, 16 flat washers, 16 shoulder washers, 8 belleview washers, 2 banana plugs, 2 fork terminals
90,-
90,-
90,-
EC-RPR-50* includes: 12 bolts, 12 nuts, 24 flat washers, 24 shoulder washers, 24 belleview washers, 2 banana plugs, 2 fork terminals
181,-
* please specify the appropriate item number that corresponds to your fuel cell

Heaters

Description:
While a PEM fuel cell will run at room temperature, it has maximum efficiency at just below the boiling temperature of water (but not over, otherwise the membrane will dry up, rendering it unable to carry protons). Therefore, heaters are recommended for the test cells to run efficiently. The silicone rubber heater is a small resistance heater pad that is attached to either end of the fuel cell. The fire rod heater also a resistive element that is inserted into a matching diameter hole in the graphite plates.

Specification and Price:

Item Description
Price €
H-SR1 silicone rubber heater for 5 cm², 25 cm², 50 cm² fuel cell; 60 W, 120 V
128,-
H-FR1 fire rod heater od 1/8", l 1,5"; 60 W, 120 V
120,-
H-FR2 fire rod heater od 1/8", l 2,0"; 100 W, 120 V
120,-
H-RP1 fiberglass rope heater 1 feet long; 60 W, 120 V
59,-
H-RP2 fiberglass rope heater 2 feet long; 104 W, 120 V
70,-

Gas Flow Back Pressure Regulator

Back flow back pressure regulators control the fuel cell operating pressure.
Gas flow back pressure regulator BPR-1: 0 - 50 psig
(0 - 3,45 bar)



price in Euro: 774,-

Swagelok™ Fittings

Description:
Swagelok™ tube fittings provide a leak proof, torque free seal at all tubing connections and eliminate costly, hazardous leaks in instrumentation and process tubing. All the action in the fittings moves along the tube axially instead of with a rotary motion. Since no torque is transmitted from the fitting to the tubing, there is no initial strain, which might weaken the tubing.

Specification:
• gaugeable tube and adaptor fitting
• available in tube sizes from 1/16 to 2 inches and 2 to 50 mm
• consistent gaugeability upon initial make up
• easy to disconnect and retighten
• wide variety of materials and configurations

Item and Price:

Item Description Price €
SWL-N-05

SWL-N-25
ylon Swagelok™ fittings; male-connector 1/4 x 1/8 NPT
Nylon Swagelok™ fittings; male-connector 1/4 x 1/16 NPT
5,60

12,95
SWL-TFL-05

SWL-TFL-25
Teflon™ Swagelok™ fittings; male-connector 1/4 x 1/8 NPT
Teflon™ Swagelok™ fittings; male-connector 1/4 x 1/16 NPT
28,60

60,50

Nylon Shoulder Washers and Teflon™ Shoulder Washers

Item Description
Price €
EC-RPR-NSW Nylon Shoulder Washers (Tie Rod Insulators) Box of 20
20,00
EC-RPR-TSW Teflon™ Shoulder Washers (Tie Rod Insulators) Box of 20
44,00

End Plates - Collector Copper Plates

Item Description
Price €
CCP-01 Gold plated current collector copper plate for 1 cm² active area
330,-
CCP-05 Gold plated current collector copper plate for 5 cm² active area
330,-
CCP-25 Gold plated current collector copper plate for 25 cm² active area
330,-
CCP-50 Gold plated current collector copper plate for 50 cm² active area
425,-
AP-50 Aluminum End plate for 50 cm² active area
284,-

Die-Cuts for Gaskets, Electrodes, MEAs

Description:
We offer a customized die-cut fit for gaskets, electrodes and MEAs. You can give us your specifications and we will design your own die-cut based on any custom design.

Die-cut for gaskets, electrodes, MEAs EC-DCUT:
Price on request


Print page
         
SEARCH

Hannover Messe 2019

Meet us at HANNOVER MESSE, April 1-5, 2019 ...
more »

 
 
Hannover Messe 2018

Meet us at HANNOVER MESSE, April 23-27, 2018 ...
more »

 
 

QuinTech
Fuel Cell Technology
Danziger Straße 8
DE-73035 Goeppingen

phone +49 (0)71 61 / 94 63 18
fax +49 (0)71 61 / 94 63 19
e-mail: quintech@quintech.de